VARIOKLAV BENCH-TOP UNITS 75 T and 135 T

Benchtop units with round sterilizing chamber - maximum utilization of laboratory workspace


One sterilizer with many advantages

  • No cheap compromises: Processes, measurements, fittings, stainless steel finishing and batch documentation compliant with DIN and industry standards
  • Fast closure - easy opening thanks to our Fingertip Quick Lock with space-saving swing door


Universal basic versions for the microbiological standard laboratory for

  • Liquids, culture media
  • Solids such as instruments, glassware and devices
  • Waste


Safe and future-proof

  • Modules available for fast cooling, prevacuum and drying and for exhaust-air filtration with condensate sterilization
  • Direct and independent batch documentation
  • Newly developed fitting blocks without dead spaces ensure sterilization quality and eliminate problem zones when sterilizing waste
  • Abundant supply of accessorie



GESAMT TISCH 007 BVARIOKLAV 75 T / VARIOKLAV 135 T

Universal basic versions for the microbiological standard laboratory for


The VARIOKLAV 75 T and 135 T steam sterilizers with their ultra-flat steam generators in their double wall combine the advantages of a double-walled device - low energy consumption, permanently ready for use, effective deaeration and drying by built-in jacket heater - with those of a single-wall device - fast cooling. The chamber is free of furnishings, after sterilization free of feed water and therefore easy to clean.

hp 65T 06 01401VARIOKLAV 65 TC

Das hochkompakte und leistungsstarke Tischgerät bietet trotz minimaler Anforderungen an die Stellfläche den gleichen Funktionsumfang wie die größeren Tischgeräte bei einer maximale Beladekapazität von 65 Liter.

  • Schmaler Stellbereich von nur B/T 525/800 mm
  • Platz für 18 quadratische 1 Liter Laborflaschen
  • Integrierter 18 Liter Vorratstank für VE-Wasser, kein externer Vorratsbehälter oder bauseitiger Speisewasseranschluss erforderlich
  • Einsatzgebiete bei hohen Anforderungen an die Sterilisierqualität, insbesondere im Pharmabereich
  • Zertifiziert als mobiles und stationäres Medizingerät (1StE) nach EN 13485 zum Sterilisieren von Medizinprodukten im Krankenhausbereich


Alle Basisgeräte sind mit vier Sterilisierprogrammen ausgestattet, zwei davon für Flüssigkeiten und je ein Verfahren für Feststoffe bzw. Müll. Bis zu 16 Programmabläufe sind entsprechend den Modulen und Ausbaustufen in der Steuerung speicherbar.

Ein bis zu achtfacher Druckwechsel kombiniert mit dem effektiven Dampfspülen verdrängt bei Feststoffen bzw. Müll die Restluft und ermöglicht schnelleres Erwärmen durch pulsierendes Einwirken von Dampf.

 


Safe and easy operation

  • Direct selection of your three most important programs
  • Extensive loading capacity of 75 and 135 litres despite narrow design
  • Convenient loading and unloading
  • Impressive loading depth of 600 and 700 mm Four height-adjustable loading levels, suitable for flasks of different sizes
  • No feed water or condensate in the chamber, a great advantage during loading and unloading
  • No heating elements in the chamber, no burning of agar
  • Wide drip ledge under door collects condensate, can be removed for cleaning


Advantages

  • Space-saving swing doors instead of slide doors - no base required
  • Automatic spent-steam condensation
  • Innovative thermolock pursuant to TRB 402* for liquids
  • Versatile control unit, simple for operators and flexible for lab management


And after your purchase?

Benefit from fast batch processing, low operating cost thanks to efficient steam managemen

Safety
The steam pressure on the lid is transferred with maximum safety to innumerably many points on the closing ring - not just to two positions as with clip locks.

Two pressure sensors check for complete pressure release before the lid can be opened Silicone seal movable by pressurized air: - uniform closing pressure, reliable seal - wedge-shaped profiles automatically retract the seal when the pressure is gone - long life

 

vi000359Unique Fingertip Quick Lock*
Never before has opening and closing a swing door been so simple and convenient. When a button is pressed, the safety ring locks the door. It is tensed pneumatically, circumferentially encloses the door and places itself immovably inside the closing ring. A movable seal closes the sterilizer chamber, making it pressure and vacuum-tight.

All Type 75 and 135 sterilizers - whether benchtop or free-standing unit - share the same features in the basic version, are easy to install thanks to the joint connection and ready to go within minutes. Double protection: The integrated compressor and external pressurized-air connector supply quick lock, lid seal and pneumatic valve and remove condensate Drain valve in the chamber floor eliminates dead spaces and thereby non-sterilizing zones, ensures a sterile condensate and prevents the spread of pathogens.

 

Back wall of chamber as steam generator
Back wall of chamber as steam generator This ultra-flat steam generator rapidly generates steam - a new milestone in steam sterilizer technology. This gives the sterilizers an unusually compact design.

Advantages

  • Steam generation and chamber are separated - stores heat and feed water, preheats the sterilizing chamber, collects and separates condensate and permits the drying of solids
  • No contamination of feed waters by drop condensates, waste, or culture media, leaving the sterile supplies free of deposits by impure steam
  • Minimum water volumes in the steam generator make economic use of heating energy and reduce the amount of water used for fast cooling
  • Water level control by exploiting the differences in heat conductivity between water and steam - no maintenance

Anschlüsse

verschluss3Die Eingänge für Betriebsmittel sind übersichtlich und gut zugängig angeordnet. Die Ausgänge für Abdampf sowie Kondensat, Vakuum und Kühlung werden entsprechend der Gerätekonfiguration in einem Sammelanschluß zusammengeführt. Durch Vermischen von Leitungswasser mit Abdampf und Kondensat kann eine Abdampfkondensation* im Sammelanschluß durchgeführt werden.


rueckwand01Universalanschluß für Speisewasser

  • Wahlweise Ansaugen aus separatem Vorratsbehälter oder Einspeisen über VE-Wasseranschluß
  • Im Gerät eingebaute Pumpe gleicht alle Druckschwankungen in bauseitigen Zuleitungen aus Automatische Niveauregelung im Dampferzeuger nicht nur bei Programmstart, sondern auch vor, während und nach dem Prozeß, sichert ständige Betriebsbereitscha





vi000386Separate Ansteuerung des Dampferzeugers
Ein umfassendes Programmpaket für Nutzraum und Dampferzeugung, das die beiden Druckräume getrennt ansteuert, erweitert das Einsatzspektrum.

Vorteile

  • Vorheizen: Dampferzeuger steht ständig unter Druck
  • Effektivere Luftentfernung durch schnellere Druckwechsel und kürzere Intervalle, besonders vorteilhaft bei Müll in Abfallsäcken
  • Die Kammer ist nach der Sterilisation frei von Kondensat, dadurch noch weniger Abdampf beim Öffnen und geringere Geruchsbelästigung bei Müll
  • Verkürzt Chargenzeiten um bis zu 30 %

 

 

 

Aquastop at sterilizer water intake avoids water damage and turns water supply lines off even in standby mode.


vi000521Media temperature controlled timing
Product temperature is attained more quickly through controlled temperature increments.
No overheating of medial, timer-controlled sterilizing times, includes flexible liquid sensor.


Separate steam generator control

A comprehensive program package for chamber and steam generation that controls both pressure chambers separately offers extra versatility. Shortens batch processing times by up to 30 %.

 

 

 

 

 

Beladekapazität 65 T 75 T 135 T
Round laboratory flasks (500 ml) 21 21-28 52
Round laboratory flasks (1.000 ml) 18 14-16 21-28
Round laboratory flasks (2.000 ml) 8 8 14
Square laboratory flasks (250 ml) 90 21 100
Square laboratory flasks (500 ml) 24 21 52
Square laboratory flasks (1.000 ml)   15 21-28
Erlenmeyer flasks (1.000 ml) 8-10 8-9 14-15
Solids ca. 30 kg ca. 25 kg ca. 30 kg
Waste ca. 30 kg ca. 25 kg ca. 30 kg

 

 

Control unit: Sterilizing parameter ranges
Sterilizing temperature: 98 - 134 °C (target value)
Sterilizing time: 1 - 999 minutes
Removal temperature: 40 - 95 °C (thermolock)
Schlüsselschalter: For program configurations
Timer: Start of sterilizing cycle by date and time
Removal pressure: 105 - 120 kPa
Customized settings can be configured by manufacturer's customer service:
Temp. increase beyond target Up to +8 K in steam gener. during heating phase
Pressure changes: 0 - 8, adjustable
For more information see Technical Specifications datasheet

 

 

Composition of batch times*
Program steps Deaeration / Heating Sterilization Steam release Cooling ST Fast cooling module
Vakuum 121° / 134 °C   90 °C RM RO RG
Liquids (min) 15 - 45 20 / 10 - 30 - 110 15 - 60 10 - 45 10 - 50
Solids (min) 15 - 30 20 / 10 2 - 4 - - - -
Waste (min) 15 - 30 - / 15 4 - 8 - - -- -
* Load: empty and fully loaded Captions: ST= forced cooling RM = jacket cooling RO/RG = with fan

 

 Technical data 65 T 75 T 135 T
External dimensions (WxDxH) (mm) 530 x 850 x 700 540 x 810 x 780 640 x 890 x 880
Internal dimensions (ØxH) (mm) (BxTxH) 325 x 630 x 325  1 StE 400 x 600 500 x 700
Loading heigh (mm) 125 170 170
Usable volume (Litres) 65 75 135
Steam generator (water vol./ total vol.) (Litres) 18 4,0 / 6,0 5,0 / 8,0
Power requirement / Heat output (kW) 9,3 / 9,0 4,8 / 4,5* 7,8 / 7,5
Power / Supply frequency (V/Hz) 3N ~ 400 / 50 3N ~ 400 / 50* 3N ~ 400 / 50
Quick lock   Bolzen-Schnellverschluß ring quick lock ring quick lock
Weight (kg) 140 150 180
Material for pressure vessel   1.4571 DIN 17440 1.4571 DIN 17440 1.4571 DIN 17440
Standards   DIN 58951-2 DIN 58951-2 DIN 58951-2
Max. operating temperature (°C) 138 138 138
Max. operating pressure / vacuum (bar) 3,0 / -1 2,5 / -1 2,5 / -1
Mark of conformity / Notified body   CE CE / 0036 CE / 0036
European Pressure Equipment Directive (category) I II II
Order No.   24325 24625 24525

 

 

 

Options Order No.
Media temperature controlled timing 24415
Separate steam generator control (preheating) 20029
Batch documentation, direct or independent 20061 und 20062
 
Module
Fast liquid cooling (RM) 20034 (RO) 20041 oder (RG) 20042
Prevacuum, simple and fractionated 20026 oder 20027
Drying, in vacuum or in sterile air stream 20028, 20031 oder 20040
Exhaust-air filtration with condensate sterilization 20068
 
Operation supply and spent steam removal
Sterile steam, spent steam condenser, aquastop, e.g. on request
 
Additional options
e.g. cooling with coiled tubing or air, stainless-steel cover, sterile venting, higher sterilizing temperatures, chamber extension / volume enlargement, prion programs, additional sterilizing programs on request
 
Accessories
Sterilization baskets, lifting jack for sterilization baskets, bases, consumables